200-105 Schulungsunterlagen & 200-105 Schulungsunterlagen & Interconnecting Cisco Networking Devices Part 2 (ICND2 V3.0) - Zendesign

Die Cisco 200-105 Schulungsunterlagen-Prüfung ist eine große Herausforderung in meinem Leben. So habe ich sehr hart gelernt. Aber das macht doch nchts, weil ich Zendesign die Schulungsunterlagen zur Cisco 200-105 Schulungsunterlagen-Prüfung gekauft habe. Zendesign ist eine Website, die Ihre alle Bedürfnisse zur Cisco 200-105 Schulungsunterlagen Zertifizierungsprüfung abdecken können. Mit den Prüfungsmaterialien von Pass4test können Sie die Cisco 200-105 Schulungsunterlagen Zertifizierungsprüfung mit einer ganz hohen Note bestehen. Obwohl wir eine volle Rückerstattung für die Verlust des Tests versprechen, bestehen fast alle Kunde Cisco 200-105 Schulungsunterlagen, die unsere Produkte benutzen.

ICND2 200-105 Dann lassen wir Zendesign Ihnen helfen!

Die Kandidaten brauchen an dem 20-tündigen Kurs teilnehmen, dann können sie neue Kenntnisse beherrschen und ihre ursprüngliches Wissen konsolidieren und auch die Cisco 200-105 - Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Schulungsunterlagen Zertifizierungsprüfung leichter als diejenigen, die viel Zeit und Energie auf die Prüfung verwendet, bestehen. Möchten Sie so schnell wie möglich die Zertifikat der Cisco 200-105 Exam Fragen erwerben? Insofern Sie uns finden, finden Sie doch die Methode, mit der Sie effektiv die Cisco 200-105 Exam Fragen Prüfung bestehen können. Die Technik-Gruppe von uns Zendesign haben seit einigen Jahren große Menge von Prüfungsunterlagen der Cisco 200-105 Exam Fragen Prüfung systematisch gesammelt und analysiert.

Aber für die Prüfung braucht man viel Zeit unf Energie, um die Fachkenntnisse gut zu lernen. Im Zeitalter heute, wo die Zeit sehr geschätzt wird, ist Zeit Geld. Das Schulungsprogramm zur Cisco 200-105 Schulungsunterlagen Zertifizierungsprüfung von Zendesign dauert ungefähr 20 Stunden.

Cisco 200-105 Schulungsunterlagen - Die Tatkraft von Menschen ist limitiert.

Warum versprechen wir, dass wir Ihnen Geld zurückgeben, wenn Sie die Cisco 200-105 Schulungsunterlagen Prüfung nicht bestehen? Denn zahlose Kunden, die unsere Prüfungssofteware benutzt haben, bestehen die Cisco 200-105 Schulungsunterlagen Zertifizierungsprüfung, was uns die Konfidenz bringt. Cisco 200-105 Schulungsunterlagen Prüfung ist eine sehr wichtige Beweis der IT-Fähigkeit für die Angestellte im IT-Gewerbe. Aber die Prüfung ist auch schwierig. Die Arbeiter von Zendesign haben die Cisco 200-105 Schulungsunterlagen Prüfungsunterlagen mit große Einsätze geforscht. Die Software ist das Geistesprodukt vieler IT-Spezialist.

Außerdem bieten wir Online Test Engine und Simulierte-Software. Sie sind auch inhaltsreich und haben ihre eingene Überlegenheit.

200-105 PDF DEMO:

QUESTION NO: 1
The command frame-relay map ip 10.121.16.8 102 broadcast was entered on the router.
Which of the following statements is true concerning this command?
A. The broadcast option allows packets, such as RIP updates, to be forwarded across the PVC.
B. This command is required for all Frame Relay configurations.
C. 102 is the remote DLCI that will receive the information.
D. The IP address 10.121.16.8 is the local router port used to forward data.
E. This command should be executed from the global configuration mode.
Answer: A
Explanation:
The command frame-relay map ip 10.121.16.8 102 broadcast means to map the remote IP
10.121.16.8 to the local DLCI 102.
When the "broadcast" keyword is included, it turns Frame Relay network as a broadcast network, which can forward broadcasts.

QUESTION NO: 2
Refer to the exhibit.
Assume that all router interfaces are operational and correctly configured. In addition, assume that
OSPF has been correctly configured on router R2. How will the default route configured on R1 affect the operation of R2?
A. Any packet destined for a network that is not referenced in the routing table of router R2 will be directed to R1. R1 will then send that packet back to R2 and a routing loop will occur.
B. The networks directly connected to router R2 will not be able to communicate with the
172.16.100.0, 172.16.100.128, and 172.16.100.64 subnetworks.
C. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately because of the lack of a gateway on R1.
D. Any packet destined for a network that is not directly connected to router R2 will be dropped immediately.
E. Any packet destined for a network that is not directly connected to router R1 will be dropped.
Answer: A
Explanation:
First, notice that the more-specific routes will always be favored over less-specific routes regardless of the administrative distance set for a protocol.
In this case, because we use OSPF for three networks (172.16.100.0 0.0.0.3, 172.16.100.64 0.0.0.63,
172.16.100.128
0.0.0.31) so the packets destined for these networks will not be affected by the default route.
The default route configured on R1 "ip route 0.0.0.0 0.0.0.0 serial0/0 will send any packet whose destination network is not referenced in the routing table of router R1 to R2, it doesn't drop anything so answers A, B and C are not correct. D is not correct too because these routes are declared in R1 and the question says that "OSPF has been correctly configured on router R2, so network directly connected to router R2 can communicate with those three subnetworks. As said above, the default route configured on
R1 will send any packet destined for a network that is not referenced in its routing table to R2;
R2 in turn sends it to R1 because it is the only way and a routing loop will occur.

QUESTION NO: 3
At which layer of the OSI model is RSTP used to prevent loops?
A. transport
B. network
C. data link
D. physical
Answer: C
Explanation: RSTP and STP operate on switches and are based on the exchange of
Bridge Protocol Data Units (BPDUs) between switches. One of the most important fields in
BPDUs is the Bridge Priority in which the MAC address is used to elect the Root Bridge ,
RSTP operates at Layer 2.
http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml

QUESTION NO: 4
What information does a router running a link-state protocol use to build and maintain its topological database? (Choose two.)
A. TTL packets from designated routers
B. routing tables received from other link-state routers
C. beacons received on point-to-point links
D. LSAs from other routers
E. SAP messages sent by other routers
F. hello packets
Answer: D,F
Explanation:
Link State Routing Protocols
http://www.ciscopress.com/articles/article.asp?p=24090&seqNum=4
Link state protocols, sometimes called shortest path first or distributed database protocols, are built around a well-known algorithm from graph theory, E. W. Dijkstra'a shortest path algorithm. Examples of link state routing protocols are:
Open Shortest Path First (OSPF) for IP
The ISO's Intermediate System to Intermediate System (IS-IS) for CLNS and IP
DEC's DNA Phase V
Novell's NetWare Link Services Protocol (NLSP)
Although link state protocols are rightly considered more complex than distance vector protocols, the basic functionality is not complex at all:
1 . Each router establishes a relationship-an adjacency-with each of its neighbors.
2 . Each router sends link state advertisements (LSAs), some
3 . Each router stores a copy of all the LSAs it has seen in a database. If all works well, the databases in all routers should be identical.
4 . The completed topological database, also called the link state database, describes a graph of the internetwork. Using the Dijkstra algorithm, each router calculates the shortest path to each network and enters this information into the route table.

QUESTION NO: 5
What can be done to secure the virtual terminal interfaces on a router? (Choose two.)
A. Enter an access list and apply it to the virtual terminal interfaces using the access-class command.
B. Configure a virtual terminal password and login process.
C. Create an access list and apply it to the virtual terminal interfaces with the access-group command.
D. Physically secure the interface.
E. Administratively shut down the interface.
Answer: A,B
Explanation:
It is a waste to administratively shut down the interface.
Moreover, someone can still access the virtual terminal interfaces via other interfaces -> A is not correct.
We can not physically secure a virtual interface because it is "virtual" -> B is not correct.
To apply an access list to a virtual terminal interface we must use the "access-class" command.
The "access-group" command is only used to apply an access list to a physical interface -> C is not correct; E is correct.
The most simple way to secure the virtual terminal interface is to configure a username & password to prevent unauthorized login -> D is correct.

Wir Zendesign haben uns seit Jahren um die Entwicklung der Software bemühen, die die Leute helfen, die in der IT-Branche bessere Arbeitsperspektive möchten, die Cisco Microsoft 070-473 Prüfung zu bestehen. Microsoft 070-486 - Bisher fiel noch keiner unserer Kandidaten durch! ISC CISSP - Dann können Sie das kundenorientierte Design von uns Zendesign erkennen und die ausführliche Deutungen empfinden.

zendesign

This entry has 1 replies

  1. Mr WordPress says:

    Hi, this is a comment.
    To delete a comment, just log in and view the post's comments. There you will have the option to edit or delete them.

Related Posts
Recent Updated Posts